- Steel, timber or aluminium leaves
- Welded steel subframe, adjustable hinges
- No headroom required
A side-hinged garage door opens outward on hinges like a pair of large doors. In Alberton it is chosen for two reasons: the garage is used as a workshop or store and needs a door that can be opened partly, or the house calls for a traditional look that an overhead door cannot give it.
Side-hinged garage doors we supply in Alberton
- Steel side-hinged doors in ribbed and panelled profiles.
- Timber side-hinged doors in hardwood or clad, for traditional elevations.
- Unequal leaf pairs so one leaf works as a normal pedestrian door.
- Glazed upper panels where the garage needs daylight.
Why a side-hinged door suits a workshop garage
You can open one leaf and walk in, which nobody does with an overhead door. On the older properties through Alberton North, Florentia and Raceview where the garage has become a workshop or storeroom, that single fact usually decides it.
Space required in front of the opening
The leaves swing outward, so the driveway apron has to be clear and reasonably level. On the ridge through Meyersdal and Meyersig a rising driveway will stop the leaves opening fully, and we will say so at survey rather than fit a door that jams on the slope every morning.
Frames, hinges and hanging
The frame carries the whole load, and on a heavy timber pair that load is considerable. We fit a proper subframe anchored into the structure, with hinges rated for the leaf mass. A side-hinged door that drops at the leading edge has almost always been hung on an inadequate frame.
Locking and security
Multi-point locking into head and threshold on the leading leaf, and shoot bolts on the slave leaf. Locking a pair of doors at the centre only is what makes them easy to force, and on an outbuilding away from the house that matters more, not less.
Side-hinged doors on industrial and store buildings
On plant and workshop sites a hinged pair is often the right door on a store, a switch room or a small workshop, because it is simple, cheap to maintain and has nothing to go wrong overhead. On a corrosive site we coat the hinges and locking to the same standard as the leaf, because those are what seize first.
Timber doors and Highveld weather
Hardwood on a west-facing opening takes strong afternoon sun and then hard summer rain, and it needs a maintained finish to cope with the swing between them. We specify the timber and the sealing for that exposure and state the maintenance interval honestly.
What a side-hinged garage door costs in Alberton
Priced on opening size, leaf material, glazing, locking and whether a new subframe is needed. Timber costs more than steel and lasts well when it is looked after.
Common questions
About side-hinged garage doors
Roughly half the opening width in clear space in front of each leaf. Check for boundary walls, steps, paving edges and where cars actually park. If the driveway falls away steeply from the garage we set the leaves higher and use a threshold seal.
Yes, with a swing-arm operator on each leaf, the same type used on driveway gates. It works well but is slower than a roll-up motor and needs the swing area kept permanently clear. Most of our side-hinged customers stay manual.
Because the leaves were hung straight onto brickwork. We fit a welded steel subframe into the reveal first, square and plumb, and hang the leaves off that with adjustable hinges so the door can be trued up later.
Often, yes. If the frame is sound and square, new leaves cost a fraction of a complete door. Send a photo of the opening from outside and we will tell you which you are looking at.
Related
Also worth a look
Industrial Roller Shutter Doors
Alrode, Alrode South, Spartan side
Heavy-duty galvanised shutters for the Alrode manufacturing belt, specified by span and duty cycle for openings up to 8 000mm wide.
- Openings to 8 000mm wide
- 0.8mm–1.2mm galvanised slat
- Chain hoist or motorised
Wooden Garage Doors
Meranti, cedar and saligna
Meranti, cedar and saligna garage doors built on a galvanised steel frame and sealed on all six faces before they are hung. Tip-up or sectional, manual…
- Timber on a galvanised steel frame
- Sealed all six faces before hanging
- Tip-up or sectional mechanism
Perforated Roller Shutter Doors
Ventilation for hot and fumed areas
Perforated curtains for welding bays, furnaces and workshops that need heat and fumes out while the opening stays covered.
- Punched galvanised slat, mixed options
- Openings to 6 000mm wide
